How do you remove and install the driveaxle in both front and rear configurations on Hyundai Santa Fe?

To remove the front axle shaft, start by taking off the wheel cover or hubcap, then remove the cotter pin and loosen the axle shaft/hub nut with a long breaker bar, followed by loosening the wheel lug nuts. Raise the vehicle securely on jackstands and remove the wheel. Drain the transaxle lubricant, disconnect the wheel speed sensor and brake hose assembly, then remove the two bolts from the lower strut and steering knuckle, pulling the knuckle free of the strut. Swing the knuckle/hub assembly out until the end of the axle shaft is free; if the splines stick, tap the end of the axle shaft with a plastic hammer and support it with wire to avoid strain on the inner CV joint. Carefully pry the inner end of the axle shaft from the transaxle using a large screwdriver or prybar, supporting the CV joints as you remove the axle shaft. For installation, pry off the old spring clip from the inner end of the axle shaft and install a new one, lubricate the differential or intermediate shaft seal with multi-purpose grease, and raise the axle shaft into position while supporting the CV joints. Insert the splined end into the differential side gear, ensuring the spring clip locks in its groove with the gap facing down. Apply grease to the outer CV joint splines, pull out on the strut/steering knuckle assembly, and install the stub axle into the hub. Reconnect the balljoint to the lower control arm and tighten the nuts according to torque specifications. Install the axle shaft/hub nut with the convex side of the washer facing out, tightening it securely but not to the actual torque specification until the vehicle is lowered. Ensure the axle shaft is seated securely in the transaxle, then install the wheel and lug nuts, lower the vehicle, and tighten the lug nuts and axle shaft/hub nut to the specified torque, installing a new cotter pin. Refill the transaxle with the recommended lubricant. For rear 4WD models, begin by removing the wheel cover or hubcap, raising the vehicle securely on jackstands, and removing the cotter pin and nut from the rear axle shaft/hub. Disconnect and lower the differential enough to pry the axle shafts out, supporting the inner ends with wire. Tap the axle shafts out of the hubs with a soft-face hammer while supporting their weight. For installation, pry off the old spring clip from the inner end of the axle shaft, install a new one, lubricate the end splines, and raise the axle shaft into position while supporting the CV joints. Insert the axle shaft into the hub and install the nut finger tight, then position the differential and insert the splined end into the differential side gear, ensuring the spring clip locks in its groove with the gap facing down. Complete the installation in reverse order, tightening the lug nuts and hub nut to the specified torque, and refill the differential with the recommended lubricant.

Genuine Hyundai Santa Fe Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

89 Axle Shafts found

View related parts
Hyundai Santa Fe Bearing Bracket & Shaft Assembly
Part Number: 49560-2B570
$310.24 MSRP: $428.42
You Save: $118.18 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft
- Replaced by: 49560-2B570--SJ
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2007-2009 Hyundai Santa Fe | DOHC - MPI | Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Hyundai Santa Fe Shaft Assembly-Drive,RH
Part Number: 49501-1U200
$448.45 MSRP: $635.60
You Save: $187.15 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Replaces: 49501-1U250
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2009-2012 Hyundai Santa Fe | DOHC - MPI | Wagon - 5Door 5P
View related parts
Hyundai Santa Fe Bearing Bracket & Shaft Assembly
Part Number: 49560-2B000
$304.77 MSRP: $420.85
You Save: $116.08 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 49560-2B000--SJ
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2006-2009 Hyundai Santa Fe | Middle Grade | DOHC - MPI | 5 Door Wagon, Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Hyundai Santa Fe Bearing Bracket & Shaft Assembly
Part Number: 49560-2P250
$304.93 MSRP: $428.42
You Save: $123.49 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Inner Shaft Assembly, Shaft
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2009-2012 Hyundai Santa Fe | DOHC - MPI | Wagon - 5Door 5P
View related parts
Hyundai Santa Fe Bearing Bracket & Shaft Assembly
Part Number: 49560-2B500
$286.62 MSRP: $402.69
You Save: $116.07 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Inner Shaft Assembly, Shaft
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2006-2009 Hyundai Santa Fe | High Grade | DOHC - MPI | 5 Door Wagon, 5 Door Wagon 7, Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Hyundai Santa Fe Shaft Assembly-Drive,LH
Part Number: 49500-2W430
$509.14 MSRP: $721.61
You Save: $212.47 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2013-2018 Hyundai Santa Fe | DOHC - GDI | Wagon - Long 5Door 6P, Wagon - Long 5Door 7P
View related parts
Hyundai Santa Fe Bearing Bracket & Shaft Assembly
Part Number: 49560-2B150
$291.61 MSRP: $402.69
You Save: $111.08 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Inner Shaft Assembly, Shaft
- Replaced by: 49560-2B150--SJ
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2006-2009 Hyundai Santa Fe | Middle Grade | DOHC - MPI | 5 Door Wagon, 5 Door Wagon 7, Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Hyundai Santa Fe Shaft Assembly-Drive,LH
Part Number: 49500-2B010
$455.03 MSRP: $644.92
You Save: $189.89 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2006-2009 Hyundai Santa Fe | Middle Grade | DOHC - MPI | 5 Door Wagon, Wagon - 5Door 5P, Wagon - 5Door 7P
View related parts
Hyundai Santa Fe Shaft Assembly-Drive,LH
Part Number: 49500-1U200
$448.45 MSRP: $635.60
You Save: $187.15 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2009-2012 Hyundai Santa Fe | DOHC - MPI | Wagon - 5Door 5P
View related parts
Hyundai Santa Fe Bearing Bracket & Shaft Assembly
Part Number: 49560-C5450
$291.81 MSRP: $409.98
You Save: $118.17 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Inner Shaft Assembly, Shaft
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2013-2018 Hyundai Santa Fe | DOHC - GDI | Wagon - Long 5Door 6P, Wagon - Long 5Door 7P
View related parts
Hyundai Santa Fe Shaft Assembly-Drive,RH
Part Number: 49501-2W450
$509.14 MSRP: $721.61
You Save: $212.47 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2013-2018 Hyundai Santa Fe | DOHC - GDI | Wagon - Long 5Door 6P, Wagon - Long 5Door 7P
View related parts
Hyundai Santa Fe Shaft Assembly-Drive,RH
Part Number: 49501-S2200
$395.03 MSRP: $559.89
You Save: $164.86 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2019-2020 Hyundai Santa Fe | DOHC - GDI | Wagon - 5Door 5P
View related parts
Hyundai Santa Fe Shaft Assembly-Drive,LH
Part Number: 49500-S1200
$447.09 MSRP: $633.66
You Save: $186.57 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2019-2020 Hyundai Santa Fe | DOHC - GDI | Wagon - 5Door 5P
View related parts
Hyundai Santa Fe Shaft Assembly-Drive,LH
Part Number: 49500-2W400
$509.14 MSRP: $721.61
You Save: $212.47 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2013-2018 Hyundai Santa Fe | DOHC - GDI | Wagon - Long 5Door 6P, Wagon - Long 5Door 7P
View related parts
Hyundai Santa Fe Shaft Assembly-Drive RR,LH
Part Number: 49600-S1000
$745.75 MSRP: $1066.34
You Save: $320.59 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly, Axle Shaft Assembly
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2019-2020 Hyundai Santa Fe | DOHC - GDI, DOHC - TCI/GDI | Wagon - 5Door 5P
View related parts
Hyundai Santa Fe Bearing Bracket & Shaft Assembly
Part Number: 49560-C5400
$291.81 MSRP: $409.98
You Save: $118.17 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Inner Shaft Assembly, Shaft
- Replaced by: 49560-C5400--SJ
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2013-2018 Hyundai Santa Fe | DOHC - GDI | Wagon - Long 5Door 6P, Wagon - Long 5Door 7P
View related parts
Hyundai Santa Fe Bearing Bracket & Shaft Assembly
Part Number: 49560-2P450
$304.93 MSRP: $428.42
You Save: $123.49 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Inner Shaft Assembly, Shaft
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2009-2012 Hyundai Santa Fe | DOHC - MPI | Wagon - 5Door 5P
View related parts
Hyundai Santa Fe Shaft Assembly-Drive RR,RH
Part Number: 49601-S1000
$619.50 MSRP: $878.03
You Save: $258.53 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly, Axle Shaft Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2019-2020 Hyundai Santa Fe | DOHC - GDI, DOHC - TCI/GDI | Wagon - 5Door 5P
View related parts
Hyundai Santa Fe Bearing Bracket & Shaft Assembly
Part Number: 49560-C5630
$273.44 MSRP: $384.18
You Save: $110.74 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2019-2020 Hyundai Santa Fe | DOHC - TCI/GDI | Wagon - 5Door 5P
View related parts
Hyundai Santa Fe Bearing Bracket & Shaft Assembly
Part Number: 49560-S2250
$273.44 MSRP: $384.18
You Save: $110.74 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2019-2020 Hyundai Santa Fe | DOHC - GDI | Wagon - 5Door 5P

| Page 1 of 5 |Next >

1-20 of 89 Results

Hyundai Santa Fe Axle Shaft

If you are looking for affordable high-quality OEM Hyundai Santa Fe Axle Shaft, then you have come to the prime place. Our website provides a large amount of genuine Hyundai Santa Fe Axle Shaft at unbeatable prices. All our parts come backed with the manufacturer's warranty.

Hyundai Santa Fe Axle Shaft Parts Questions & Experts Answers

Shaft Assembly-Drive,LH
49500-1U200
Q: How do you remove and install the driveaxle in both front and rear configurations on Hyundai Santa Fe?
A: To remove the front axle shaft, start by taking off the wheel cover or hubcap, then remove the cotter pin and loosen the axle shaft/hub nut with a long breaker bar, followed by loosening the wheel lug nuts. Raise the vehicle securely on jackstands and remove the wheel. Drain the transaxle lubricant, disconnect the wheel speed sensor and brake hose assembly, then remove the two bolts from the lower strut and steering knuckle, pulling the knuckle free of the strut. Swing the knuckle/hub assembly out until the end of the axle shaft is free; if the splines stick, tap the end of the axle shaft with a plastic hammer and support it with wire to avoid strain on the inner CV joint. Carefully pry the inner end of the axle shaft from the transaxle using a large screwdriver or prybar, supporting the CV joints as you remove the axle shaft. For installation, pry off the old spring clip from the inner end of the axle shaft and install a new one, lubricate the Differential or intermediate shaft seal with multi-purpose grease, and raise the axle shaft into position while supporting the CV joints. Insert the splined end into the differential side gear, ensuring the spring clip locks in its groove with the gap facing down. Apply grease to the outer CV joint splines, pull out on the strut/steering knuckle assembly, and install the stub axle into the hub. Reconnect the balljoint to the lower control arm and tighten the nuts according to torque specifications. Install the axle shaft/hub nut with the convex side of the washer facing out, tightening it securely but not to the actual torque specification until the vehicle is lowered. Ensure the axle shaft is seated securely in the transaxle, then install the wheel and lug nuts, lower the vehicle, and tighten the lug nuts and axle shaft/hub nut to the specified torque, installing a new cotter pin. Refill the transaxle with the recommended lubricant. For rear 4WD models, begin by removing the wheel cover or hubcap, raising the vehicle securely on jackstands, and removing the cotter pin and nut from the rear axle shaft/hub. Disconnect and lower the differential enough to pry the axle shafts out, supporting the inner ends with wire. Tap the axle shafts out of the hubs with a soft-face hammer while supporting their weight. For installation, pry off the old spring clip from the inner end of the axle shaft, install a new one, lubricate the end splines, and raise the axle shaft into position while supporting the CV joints. Insert the axle shaft into the hub and install the nut finger tight, then position the differential and insert the splined end into the differential side gear, ensuring the spring clip locks in its groove with the gap facing down. Complete the installation in reverse order, tightening the lug nuts and hub nut to the specified torque, and refill the differential with the recommended lubricant.