×
- Live Chat
- 1-888-788-8214
My Garage
My Account
Cart
Genuine Hyundai Excel Rocker Arm
Engine Rocker Arm- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
6 Rocker Arms found
Hyundai Excel Rocker Arm D
Part Number: 24554-24304$31.15 MSRP: $43.39You Save: $12.24 (29%)Ships in 1-3 Business Days
Hyundai Excel Rocker Arm C
Part Number: 24553-24304$32.04 MSRP: $44.63You Save: $12.59 (29%)Ships in 1-3 Business Days
Hyundai Excel Rocker Arm Arm
Part Number: 24527-21300$19.31 MSRP: $25.56You Save: $6.25 (25%)Ships in 1-3 Business DaysHyundai Excel Rocker Arm B
Part Number: 24528-21300$19.83 MSRP: $26.26You Save: $6.43 (25%)Ships in 1-3 Business Days
Hyundai Excel Rocker Arm D
Part Number: 24554-24300$32.23 MSRP: $43.39You Save: $11.16 (26%)Ships in 1-3 Business DaysHyundai Excel Rocker Arm C
Part Number: 24553-24300$33.15 MSRP: $44.63You Save: $11.48 (26%)Ships in 1-3 Business Days
Hyundai Excel Rocker Arm
If you are looking for affordable high-quality OEM Hyundai Excel Rocker Arm, then you have come to the prime place. Our website provides a large amount of genuine Hyundai Excel Rocker Arm at unbeatable prices. All our parts come backed with the manufacturer's warranty.
Hyundai Excel Rocker Arm Parts Questions & Experts Answers
- Q: How to remove, inspect, and install the rocker arm assemblies on Hyundai Excel?A: To remove the valve cover, position the number one piston at Top Dead Center and check each rocker arm assembly for identification marks, marking their positions for correct installation; the rear assembly is Intake and the front is Exhaust. Progressively loosen the bolts on each assembly to relieve valve spring pressure without removing the bolts from the shafts, which will hold the rocker arms in place when the shaft assembly is removed. For 1995 and later models, wrap vinyl tape around the rocker arm and hydraulic lash adjuster to prevent the adjuster from falling out. Lift the rocker arm assemblies away from the Cylinder Head with the retaining bolts and washers still in place. Mark the shafts at the Timing Belt end as Intake and Exhaust, noting that the timing belt end has larger chamfered edges. Remove the rocker arms and springs one at a time, keeping components in order for reassembly; on 1994 and earlier models, the exhaust rocker shaft springs are shorter than the intake springs. Clean and inspect all components for wear or damage, checking specific parts based on the model year. Lubricate bearing surfaces with engine assembly lube or clean engine oil, then reassemble the shafts in reverse order, ensuring correct installation of rocker arms based on markings and cylinder numbers. For 1994 and earlier models, adjust the lash adjusters to protrude approximately 0.04 inch. For 1995 and later models, bleed air from the hydraulic lash adjusters by submerging them in diesel fuel and working the plunger. Position the rocker arm assemblies on the cylinder head and alternately tighten the bolts until fully seated, then torque them in stages. Adjust valve clearances for 1994 and earlier models, install remaining parts in reverse order, and run the engine to check for oil leaks and proper operation, adjusting valves while warm for earlier models and addressing any noise from lash adjusters in later models by varying engine speed.
