How do you remove and install the hood on Hyundai Elantra?

The hood is somewhat difficult to adjust and rotate; therefore, this process should be done by at least two persons. Start by lifting the car and putting blankets or pads on the fenders and the cowl area to avoid body and paint damages. Any cables or wires that may hinder the removal process should be disconnected: the windshield washer tubing from the nozzles on the hood in this instance. Place an 'x' at the side of the hood or draw a line around the hood hole before removing it for better repositioning. For the year 2007 post the locator use a small screwdriver to pull out the upper retaining clip and remove the hood support strut. The other set should be loosened from the inside by an assistant as you hold the hood, then take off the hinge-to-hood bolts and raise the hood. The process of installation is the exact opposite of what has been mentioned above, and the bolts of the hinge are placed into the marks identified. For regulation, one can shift hinge plate slot after removing the bolts or nuts in order to align in the fore-and-aft as well as on the side-to-side. Write a line around the hinge plate to show distance traveled; then, using a wrench, unscrew the bolts or nuts and move the hood slightly at a time, tightening the hinge bolts when you test the position. If required, reposition the entire hood latch assembly up-and-down and left-right on the radiator support and ensure that it properly and tightly closes against the fenders before tightening and marking the dimensions of the latch. Last but not the least, it is essential to align the hood of the car by using the adjusting screws present on the side of the radiator support and moving the hood bumpers clockwise or counter clockwise to decrease the hood height, or increase the fender height while closing the same; this enables one to keep the car's hood closed properly against the fenders of the car. The opening hood and backup light assembly and the hood hinges should be lubricated by lithium-base grease sometimes in order to address lacks of proper lubrication or wear.

Genuine Hyundai Elantra Hood

Engine Hood

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Hoods found

View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-F2000
$775.41 MSRP: $1206.00
You Save: $430.59 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hood
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2016-2018 Hyundai Elantra | DOHC - MPI, DOHC - TCI/GDI | Sedan - 4Door 5P
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-F3000
$777.73 MSRP: $1209.61
You Save: $431.88 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hood
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2016-2018 Hyundai Elantra | DOHC - MPI, DOHC - TCI/GDI | Sedan - 4Door 5P
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-3X000
$336.19 MSRP: $518.28
You Save: $182.09 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hood
- Replaces: 66400-3Y000
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2011-2015 Hyundai Elantra | DOHC - GDI, DOHC - MPI | Coupe - 2Door 5P, Sedan - 4Door 5P
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-3Y000
$342.10 MSRP: $518.28
You Save: $176.18 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 66400-3X000
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2011-2015 Hyundai Elantra | DOHC - MPI | Sedan - 4Door 5P
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-2H010
$571.20 MSRP: $880.58
You Save: $309.38 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hood
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2006-2010 Hyundai Elantra | High Grade, Middle Grade | DOHC - MPI | 4 Door Sedan, Sedan - 4Door 5P
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-F2500
$677.58 MSRP: $1053.84
You Save: $376.26 (36%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Hood
- Replaces: 66400-F3500
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2019-2020 Hyundai Elantra | DOHC - MPI, DOHC - TCI/GDI | Sedan - 4Door 5P
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-AA000
$752.52 MSRP: $1170.40
You Save: $417.88 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hood
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2021-2023 Hyundai Elantra | DOHC - GDI, DOHC - MPI, DOHC - TCI/GDI | Sedan - 4Door 5P
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-AB000
$678.04 MSRP: $1054.56
You Save: $376.52 (36%)
ADD TO CART
Product Specifications
- Other Name: Hood
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2021-2023 Hyundai Elantra | DOHC - MPI | Sedan - 4Door 5P
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-F3500
$693.80 MSRP: $1053.84
You Save: $360.04 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 66400-F2500
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2019-2020 Hyundai Elantra | DOHC - MPI, DOHC - TCI/GDI | Sedan - 4Door 5P
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-28100
$288.04 MSRP: $432.65
You Save: $144.61 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 66400-28101
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1991-1995 Hyundai Elantra | High Grade, Middle Grade | 4 Door
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-28101
$283.11 MSRP: $432.65
You Save: $149.54 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hood
- Replaces: 66400-28100
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1991-1995 Hyundai Elantra | High Grade, Middle Grade | 4 Door
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-28510
$283.11 MSRP: $432.65
You Save: $149.54 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hood
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1991-1995 Hyundai Elantra | High Grade, Middle Grade | 4 Door
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-2D521
$830.69 MSRP: $1291.98
You Save: $461.29 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hood
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2000-2006 Hyundai Elantra | High Grade, Middle Grade | 4 Door Sedan, 5 Door Sedan
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-2D520
$492.63 MSRP: $713.98
You Save: $221.35 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hood
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2000-2006 Hyundai Elantra | High Grade, Middle Grade | 4 Door Sedan, 5 Door Sedan
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-29010
$450.84 MSRP: $695.04
You Save: $244.20 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hood
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1995-2000 Hyundai Elantra | High Grade, Middle Grade | 4 Door, 5 Door Wagon 5
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-29510
$464.92 MSRP: $716.74
You Save: $251.82 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hood
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 1995-2000 Hyundai Elantra | High Grade, Middle Grade | 4 Door, 5 Door Wagon 5
View related parts
Hyundai Elantra Panel Assembly-Hood
Part Number: 66400-2D020
$685.03 MSRP: $1065.44
You Save: $380.41 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hood
- Warranty: This genuine part is guaranteed by Hyundai's factory warranty.
Fits the following Vehicles:
- 2000-2006 Hyundai Elantra | High Grade, Middle Grade | 4 Door Sedan, 5 Door Sedan

Hyundai Elantra Hood

If you are looking for affordable high-quality OEM Hyundai Elantra Hood, then you have come to the prime place. Our website provides a large amount of genuine Hyundai Elantra Hood at unbeatable prices. All our parts come backed with the manufacturer's warranty.

Hyundai Elantra Hood Parts Questions & Experts Answers

Panel Assembly-Hood
66400-3X000
Q: How do you remove and install the hood on Hyundai Elantra?
A: The hood is somewhat difficult to adjust and rotate; therefore, this process should be done by at least two persons. Start by lifting the car and putting blankets or pads on the Fenders and the cowl area to avoid body and paint damages. Any cables or wires that may hinder the removal process should be disconnected: the windshield washer tubing from the nozzles on the hood in this instance. Place an 'x' at the side of the hood or draw a line around the hood hole before removing it for better repositioning. For the year 2007 post the locator use a small screwdriver to pull out the upper retaining clip and remove the hood support strut. The other set should be loosened from the inside by an assistant as you hold the hood, then take off the hinge-to-hood bolts and raise the hood. The process of installation is the exact opposite of what has been mentioned above, and the bolts of the hinge are placed into the marks identified. For regulation, one can shift hinge plate slot after removing the bolts or nuts in order to align in the fore-and-aft as well as on the side-to-side. Write a line around the hinge plate to show distance traveled; then, using a wrench, unscrew the bolts or nuts and move the hood slightly at a time, tightening the hinge bolts when you test the position. If required, reposition the entire Hood Latch assembly up-and-down and left-right on the radiator support and ensure that it properly and tightly closes against the fenders before tightening and marking the dimensions of the latch. Last but not the least, it is essential to align the hood of the car by using the adjusting screws present on the side of the radiator support and moving the hood bumpers clockwise or counter clockwise to decrease the hood height, or increase the fender height while closing the same; this enables one to keep the car's hood closed properly against the fenders of the car. The opening hood and backup light assembly and the Hood Hinges should be lubricated by lithium-base grease sometimes in order to address lacks of proper lubrication or wear.